High Quality Intake System Cleaner With Cleaning Agent Engine Carbon Deposit Cleaner

High Quality Intake System Cleaner With Cleaning Agent Engine Carbon Deposit Cleaner

Product introduction:

The model TD-501 Engine depth carbon removal washing machine developed by our company, combining with the most effective carbon remover, is the best machine to dislodge the engine fouling. It can be combined with regular vehicle maintenance and special carbon removal repairs and no need to disassemble the engine. The engine fuel supply pipe can be connected by a connector. Plug the engine back into the pipe with a plug, and then add a fixed fuel mixture decarbonizer, and allow the decarburizer to enter the engine fuel system under normal operating conditions. Carbon sludge, colloid and lacquer contaminants from injector needle valves and fuel chamber components can be dissolved within 30 minutes. 

Parameters:

The carbon deposit in the intake valve:

Since the operation of each piston of the whole engine is not synchronized, when the engine is extinguished, the intake valves of some cylinders cannot be completely closed, and some unburned fuel is continuously evaporated and oxidized, which will produce some in the intake pipe, especially behind the throttle. Soft black carbon deposits. On the one hand, these carbon deposits will roughen the pipe wall of the intake pipe, and the intake air will generate vortices in these rough places, affecting the intake effect and the quality of the mixture.

On the other hand, these carbon deposits will block the idle speed channel, causing the idle speed control device to be stuck or beyond its adjustment range, which will result in low idle speed, idling, various speeds of the attachments, failure to collect oil, and exhaust. Excessive standards, oil and other phenomena.

If you are experiencing slow acceleration during driving, tempering and tempering, and difficulty in cold start, your car's valve is likely to have accumulated carbon. It is found that the idle speed is low and the car is shaking when idling. When the accelerator is pressed, the card is issued and the battery is not idling. Then the air intake pipe of your car has accumulated carbon. With the above phenomenon, you should go to the professional repair shop to check the car in time.

Therefore, it is essential to clean the carbon in time. After cleaning carbon by TD-501 engine carbon cleaner, the car will make a good performance again. The engine noise disappeared, the air pollution reduced, the engine power increased.

Product Feature:

1. It needs to use the different chemical cleaning agent to clean the different engine parts.

2. One machine can clean three way catalytic converter by water based or oil based.

3. The cleaning agent can clean the combustion chamber and also can soak the spark plugs if there is a need.

4. It can clean carbon for five engine system parts: Three way catalytic converter, combustion chamber, fuel system, spark plug and intake valve.

5. After carbon removal ,20% engine power is increased, 70% pollution is reduced, the engine noise is decreased, oil consumption is reduced.

Engine Carbon Cleaner FAQ:

1. What is the working principle of TD-501?

Our cleaning agent is matched with the machine, and the organic solvent is mixed with the carbon in the car to achieve the effect of removing carbon from the car.

2. What effect can the car achieve after cleaning with TD-501?

After cleaning, the vehicle's power is improved, the idle speed is stable, the start is smooth, the fuel consumption is reduced, the exhaust emissions are more environmentally friendly, and the performance is restored as new.

3. When do I need to carbon clean my car?

We recommend servicing your vehicle every 15,000km or 6 months, whichever come first.

4. Can it use for diesel vehicles?

No, it can only clean the petrol cars.

5. What’s the function of the endoscope?

It can help to see the effect in the engine part, which is good for marketing.

1. How can I get the cleaning agent suitable for the machine?

You can purchase from our company and you also can get it from your local market if there is not convenient for importing such goods.

The using methods of endoscope:

Endoscope is mainly suitable for observing places that are not normally seen in the interior of a car. It is equipped with a curved probe that can be extended to the interior of the vehicle. And it also have a large high-definition display screen, which can observe the parts inside the automobile engine and facilitate observation and maintenance. Connect the power to 12V, turn on the display switch, extend the probe to the parts to be observed, you can see the points to be observed from the display.

Cleaning methods of intake manifold and throttle:

Turn the valve cleaning fluid under the cap, pour the necessary cleaning liquid into the tank and tighten the cap. Note: the gasket must not be left out and the cap must be tightened.

Connect the air source, the air source for 4-6Kg/cm2 compressed air. (Notice: pressure regulating valves and needle valves must be closed before compressed air connected to, prohibit exceeding 8/Kg/cm2 pressure)

Pull out a little bit the "left" knob of the air pressure regulating valve of the cleaning machine, then rotate the pressure regulating valve clockwise, and start the engine, running at normal idle speed, that is, carry on the cleaning work, (the pressure regulating valve rotates clockwise to boost the pressure, Rotating counterclockwise to decompression, pressure regulating EFI vehicle is about 2.5kg / cm2, fuel truck is about 2Kg/cm2 pressure, but must be adjusted according to the pressure required by the engine of the vehicle)

Open the hood (engine) and remove one of the most convenient intake manifold (throttle)

Start the engine , running at idle speed

Take out a special atomization connector, connecting to the cleaning pipe of the equipment, and put it into the inlet pipe that the engine has just taken down. Open the atomizing fluid line and spray clean the atomizing joint for about 8 minutes to 10 minutes.

After cleaning finished, firstly, close the pressure  regulating valve of the equipment to the left, and then take out the atomizing joint pipe

Turn off the engine and connect it back to the engine intake pipe as it is.

Cleaning the machine for convenient to use it next time